CL tooth coupling

CL tooth coupling (JB/ZQ 4218-86)   ¡öMarked example£º ¡ñCL3 series tooth coupling   Drive end£ºY hole of shaft£¬A keyway£¬d1=45©L£¬L=112©L   Driven end£ºY hole of shaft£¬A keyway£¬d2=45©L£¬L=112©L   CL3 coupling45X112 JB/ZQ 4218-86 ¡ñCL3 series tooth coupling   Drive end£ºY hole of shaft£¬A keyway£¬d1=45©L£¬L=112©L   Driven end£ºY hole of shaft£¬A keyway£¬d2=45©L£¬L=112©L   CL3 coupling  JB/ZQ 4218-86 CL tooth coupling(main sizes and parameters)(JB/ZQ4218-86) model Rated torque Tn (N¡¤m) allowed speed [n] (r/min) Diameter of shaft hole d1¡¢d2¡¢d3 L of hole shafA B D D1 D2 C C1 C2 e rotary inertia (kg.©O) weight (kg) Y J1 Z1 L (mm) CL1 710 3780 18,19 42 30 49 106 170 110 55 16 - - 12 0.03 7.8 20,22,24 52 38 6 18.5 18.5 25,28 62 44 2.5 14 18.5 30,32,35,38 82 60 11 - 40 112 84 CL2 1400 3000 30,32,35,38 82 60 75 134 185 125 70 2.5 13 22 12 0.05 12.5 40,42,45 112 84 28 48,50     model Rated torque Tn (N¡¤m) Allowed speed [n] (r/min) Diameter of shaft hole d1¡¢d2¡¢d3 length of shaft hole A B D D1 D2 C C1 C2 e Rotary inertia (kg.©O) weight (kg) Y J1 Z1 L (mm) CL3 3150 2400 40,42,45 112 84 92 170 220 150 90 2.5 15 28 18 0.13 26.9 48,50,55,56 60 142 107 36 CL4 5600 2000 45,48,50 112 84 125 200 250 175 110 2.5 21 28 18 0.21 34.9 55,56 60,63,65,70 142 107 17 36 71,75 CL5 8000 1680 50,55,56 112 84 145 220 290 200 130 5 30 40 25 0.45 55.8 60,63,65,70 142 107 71,75 80,85,90 172 132 CL6 11200 1500 60,63,65 142 107 160 246 320 230 140 5 25 - 25 0.70 79.9 70,71,75 80,85,90,95 172 132 100,110 212 167 CL7 18000 1270 35,70,71,75 142 107 185 286 350 260 170 5 40 40 30 1.15 109.5 80,85,90,95 172 132 25 45 100,110,120 212 167 CL8 22400 1140 80,85,90,95 172 132 210 325 380 315 190 5 35 45 30 2.38 133.8 100,110,120,125 212 167 30 130,140 252 202 CL9 28000 1000 90,95 172 132 220 335 430 365 210 5 40 - 30 3.55 171 100,110,120,125 212 167 30 130,140,150 252 202 160 302 242 CL10 50000 85 110,120,125 212 167 245 365 490 420 260 5 30 - 30 7.00 275.8 130,140,150 252 202 160,170,180 302 242 CL11 71000 750 120,125 212 167 280 405 545 470 330 5 40 - 35 13.75 385 130,140,150 252 202 160,170,180 302 242 35 190,200,220 352 282   model Rated torque Tn [N¡¤m] Allowed speed [n] (r/min) Diameter of shaft  hole d1¡¢d2¡¢d3 length of hole A B D D1 D2 C C1 C2 e Rotary inertia (kg.©O) weight (kg)     Y J1 Z1         L     (mm)     CL12 100000 560 140,150 252 202 350 485 590 520 340 5 45 - 35 21.25 540     160,170,180 302 242 38     190,200,220 352 282     240,250 410 330     CL13 140000 600 160,170,180 302 242 375 524 680 590 380 7.5 45 - 40 40.00 798.3     190,200,220 352 282     240,250,260 410 330     280 470 380     CL14 200000 540 180 302 242 405 565 730 650 420 7.5 50 - 40 53.75 976.6     190,200,220 352 282     240,250,260 410 330     280,300,320 470 380     CL15 250000 480 200,220 352 282 480 644 780 700 480 7.5 50 - 40 81.25 1182.5     240,250,260 410 330     280,300,320 470 380     340,360 550 450     CL16 355000 425 240,250,260 410 330 535 720 900 785 530 10 - - 50 150 1936     280,300,320 470 380     340,360,380 550 450     400 650 540     CL17 560000 380 260 410 330 625 800 1000 885 630 10 - - 50 285 2700     280,300,320 470 380     340,360,380 550 450     400,420,440,450 650 540     CL18 710000 330 300,320 470 380 710 900 1100 990 710 10 - - 50 400 3669     340,360,380 550 450     400,420,440,450 650 540     460,480,500     CL19 1000000 300 360,380 550 450 730 910 1250 1090 800 15 - - 60 675 5138     400,420,440,450 650 540     460,480,500 800 680     530,560     ×¢£º¢ÙThe quality and rotary inertia of coupling are the approximation calculated by the min diameter and max length of shaft hole. ¢Údiameter of shaft hole dz£¼140mm¡£ ¢ÛJ1 shaft hole: according to the requirements ,there is also no need of shaft end plate. ¢ÜThe standard applies to old products.